1. Machine Body
The machine body is composed by foundation, top rail, slider block, working table, lower cylinder, upright column, locknut and adjusting nut. The precision is adjusted by adjusting nut and the locknut fixed on the top rail. 2. Main Cylinder
3. Slider
The movement of the slider is achieved by four vertical column guidance. The guide sleeve between slider and vertical column is alloy material with good abrasion resistance and easy replacement measures after abrasion. The below platform has equipped with T type slot to make the mold stable, the detailed dimension can be provided under the requirement.
4. Lifting cylinder
Lifting cylinder is a piston type cylinder equipped in the middle hold of the foundation to work for the top or drawing process.
5. Upright Column and lockout
The material of upright column is 45# forged steel, and has process in drawing temper, the quenching hardness of the upright colume surface can reach HRC42-50. The material of Locknut is 45# forged steel, and has produced in blue handle, the connection between the upright colume and locknut is screw thread connection.
6. Stroke limit device
The stroke limit device is equipped in the left side of the machine to control the stroke distance for the slider. It is composed by parallels, angle iron, induction block and contactless switch. Two parallels iron is fixed in the worktalbe and top rail to fix angle iron, there are guide groove in the angle iron ajust the travel switch and the stroke of the slider will be controlled.
7. Hydraulic pressure station
The hydraulic pump is composed by fuel tank, axial plunger pump, motor, two way cartridge valve, oil filter and air cleaner.
(1)The tanker is welded by Q235 Steel, the front end is equipped with a pressure gauge for a easy obersation of the pressure and pressure-adjustment. In the lower part of the bracket is equipped with a pressure gauge level gauge, to observe the level. Open the upper cover, for fuel filling. In the fuel tank is provided with a cleaning mouth, open cover capable of cleaning the tank.
(2)Fuel tank for the steel plate welded structure, by shot peening and rust prevention treatment, there are clean mouth in the side of tank and oil level ruler. The air clear, valve integrated blocks are in ordered arrangement in the top of tanker cover.
Hydraulic System
Hydraulic System is composed by energy conversion device(Pump and hydro-cylinder) and energy delivery device(Tanker and pipeline). By means of electrical control system, drive slide block to complete a variety of operation cycle. The hydraulic system uses large flow cartridge valve. In the pump inlet equipped with oil fume filter to prevent impurities from entering the hydraulic system and guarantee the normal working of the oil-way. System equipped with oil-level display and oil-temperature display and also air filter. Tanker is steel welded, tanker side has cleaning window, bottom equipped with plug screw forOil drain and sewer.
To prevent the slider out of control and be down, the machine equipped with Hydraulic support safety circuit. In a piston master cylinder cavity adopts hydraulic support safety circuit to make sure the sercurity.
This machine has the adjustment, semi-automatic mode choose.
Electrical control system
(1)The machine has independent electrical control cabinet and moveable button station.
The electrical control cabinet is used to equip Power control unit, for example, The control of total power and motor starting control element and also Protection switch and a leakage protector. There are Ventilation facilities within the cabinet and with a good seal to provent the ingress of the dust. The installation location of the cabinet should be instructed by the buyer(The producer or the supplier will notify in advance)
(2)the machine standard power is AC380V/50HA, control electronic power is AC220V, Pilot valve magnet power supply for DC24V.
| Nominal Force |
2000KN |
| Ejecting force |
400KN |
| The Max. working pressure of the fluid |
25MPA |
| Max. Open Height |
1100MM |
| Max. Slide block stroke |
700MM |
| On top of the piston stroke |
250MM |
| Working table Dimension |
Left-Right |
1000MM |
| Front-Back |
900MM |
| Ram Speed |
Empty |
100MM/S |
| Working |
6-8MM/S |
| Return |
52MM/S |
| Motor Power |
15KW |
Audited Supplier 
){kind=link}
){kind=link}